Shaft repair sleeve which can be used on worn, scratched or run-in areas such as the crankshaft or pinion shaft.
If a shaft is heavily worn or scratched and can therefore no longer be properly sealed by the oil seal, this Speedi-Sleeve repair sleeve is used.
The 0.2 mm thick chrome steel sleeve is pressed over the shaft using the tool supplied.
Because the shaft is only applied a little, an oil seal with the original dimensions can still be used.
Shaft diameter: 17.0 mm
Width of usable running surface: 7.9 mm
Material: special, polished chrome steel
Installation instructions:
- Before installation, mount the crankshaft bearing on the shaft if necessary, as this can no longer be pressed over the shaft later.
- Clean the seal sliding surface on the shaft. Remove any unevenness with an abrasive cloth; the sleeve must not be positioned over keyways, holes, threads or other recesses
- Determine the installation position of the repair sleeve on the worn seal sliding surface and mark it precisely. The sleeve must completely cover the damaged area.
- Drive the repair sleeve onto the shaft with light, centric strokes against the impact cap. If the impact cap is too short, a piece of pipe can be used instead. The inside diameter should correspond to that of the impact cap. Make sure that the functional surface of the sleeve is not damaged.
- Do not use any heat during assembly, the use of adhesive is not necessary.
- In the case of large grooves or notches, the sleeve can be pressed on together with some permanently elastic sealing compound.
- If necessary, the flange can be removed by slitting the outer part and using needle-nose pliers.
- Then check everything again for damage and any burrs.
A detailed assembly instruction in English with pictures is included.
Further repair guides, as well as help with fitting oil seals, can be found in the accessories section.
Quality product from the world's leading ball bearing manufacturer SKF.
| Manufacturer | SKF |
| Material | Chrome steel (colloquially known as stainless steel) |
| Number of components | 2 pcs |
| Universal | |
| Puch | E50 ZA50 (air-cooled) ZA50 (fan-cooled) Z50 (X30 Sport) Z50 (X30 Velux) 2-speed MS, MV, MV50 3-speed VSD, DS, VZ, MC |
| Sachs | 50/3 50/4 - MLFB (2.6 PS) , LKH (4.5 PS) |
| Pony / Cilo (Beta 521 & 512) | Beta 512 Beta 521 (engine) |
| Tomos |
Ratings
Accessories & related products
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Material: Silicone · Contents: 70 ml · Color: gray · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Temperature resistance (min.): -60 - 315 °C · Gap dimension (max.): 2 mm · Area of application: Chemistry
EUR 23.60
EUR 337.14/l
Elring Dirko HT sealing compound red (silicone) high temp. 70 ml elastic up to 315°C
Temperature resistance (min.): -60 - 300 °C · Manufacturer: Elring · Color: red · Hazard warning: Causes serious eye irritation · Signal word: Attention · Contents: 70 ml · Hazard pictogram: GHS07 - Caution dangerous · Gap dimension (max.): 2 mm · Area of application: Chemistry
EUR 27.20
Not in stock
EUR 388.57/l
Explore categories from Engine block
Moped fans also bought
swiing® revival 17" rear fender Inox | Puch Maxi N
Manufacturer: swiing® revival parts · Material: Chrome steel (colloquially known as stainless steel) · Surface: polished · Color: Chrome · Wheel size: 17 " · Folding the ends: closed folded · Folding the ends: not folded · Shape of the mudguard: angular · Total length over ends: 625 mm · Scope: 940 mm · Wide mudguard profile: 82 mm · Mounting type: Nuts & bolts · Height of mudguard profile: 35 mm · Total height from support surface to top edge: 285 mm
EUR 45.00
Magura adjusting screw brake long
Manufacturer: Magura · Material: Brass · Surface: nickel-plated · Color: silver · Thread type: MF6x0.75 (fine pitch thread) · Ø shaft: 6 mm · Total length: 47 mm · Total length: 65 mm · Ø External head: 9.1 mm · Drive: Knurled screw · Shank length: 11 mm · Thread length: 24 mm
EUR 4.65
Motorex engine oil (gear oil) manual 450 ml
Manufacturer: Motorex · Oil type: GL4 · Viscosity (SAE): 80W · Contents: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Temperature resistance (min.): -30 - 220 °C · Area of application: Gearbox lubrication with clutch
EUR 12.90
EUR 28.67/l
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
