Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
| Material | Aluminum |
| Surface | blank |
| Ø axle | 12 mm |
| Ø inside | 30 mm |
| Ø Receptacle | 93 mm |
| Ø drum | 80 mm |
| Number of spoke holes | 36 pcs |
| Area of application | Standard, Custom |
| Puch |
Accessories & related products
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Ø nipple: 3.5 mm · Ø nipple: 6 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Cable length: 2200 mm · Nipple length: 10 mm · Area of application: Standard · Number of components: 1 pcs
EUR 2.85
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Total length: 190 mm · Ball bearing closed: Yes · Width: 8 mm · Width: 9 mm
EUR 36.50
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø axle: 12 mm · Ø outside: 91 mm · Ø External brake pads: 80 mm · Total length: 187 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm
EUR 82.60
swiing® revival rear brake anchor plate | Puch Maxi N
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø axle: 12 mm · Ø outside: 92 mm · Ø External brake pads: 80 mm · Total length: 135 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 10 mm · Brake lever length (lever length): 68 mm
EUR 88.50
Magura set screw M6x34 mm lock nut SW10
Slotted: No · Manufacturer: Magura · Width across flats nut: 10 mm · Width across flats Screw: 8 mm · Material: Brass · Thread type: M6x1 (standard thread) · Surface: nickel-plated · Ø cable holder: 3.05 mm · Total length: 34 mm · Ø Receptacle: 7.05 mm · Thread length: 23 mm
EUR 2.95
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Total length: 185 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 28 mm · Thread length: 52 mm · Ø shaft: 11.95 mm · Shank length: 99 mm · Width across flats SW: 7 mm
EUR 11.70
SKF 16101 2RS1 ball bearing 12/30/8
Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 16101 · Inner ring width: 8 mm · Manufacturer: SKF · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Ø inside: 12 mm · Bearing type: Deep groove ball bearing · Ø outside: 30 mm · Ball bearing closed: Yes · Width: 8 mm · Area of application: Standard
EUR 19.30
Moped fans also bought
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Manufacturer: GPO · Material: Aluminum · Surface: sandblasted · Ø cylinder: 38 mm · Total length: 135 mm · Height: 55 mm · Number of fixing points: 4 pcs · Candle thread: short · Area of application: Standard · Hole pattern [mm]: 44 x 44 · Decompressor: No · Width: 125 mm
EUR 38.90
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Quantity: 36 pcs · Surface: raw · Color: silver · Length from hook: 188 mm · Ø spoke: 2.9 mm · Ø spoke head: 5.35 mm · Nominal diameter (thread): 3.15 mm · Thread length: 11 mm · Nipple length: 14 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 °
EUR 64.90
swiing® ingenious wheel axle with bearing conversion kit spoke hub front Ø 29 mm | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Thread type: MF12x1 (fine pitch thread) · Surface: galvanized (blue) · Ø inside: 12 mm · Width across flats SW: 19 mm · Ø outside: 29.02 mm · Total length: 165 mm · Height: 5.9 mm · Height: 9.9 mm · Thread length: 40.5 mm · Thread length: 50 mm · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Ball bearing closed: Yes · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm
EUR 46.00
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø axle: 12 mm · Ø outside: 91 mm · Ø External brake pads: 80 mm · Total length: 187 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm
EUR 82.60
Collection only possible with online purchase and appointment.
