Stage6 adapter intake manifold PWK carburetor from 30 mm

Sealing paper set 4 pcs.

Manufacturer: Made in Spain · Material: Sealing carton · Material: Sealing paper · Place of use: Universal · Thickness: 0.25 mm · Thickness: 0.4 mm · Thickness: 0.5 mm · Thickness: 1.2 mm

Stage6 R/T RT-PWK 28 mm carburetor "Black-Edition"

Nominal diameter: 28 mm · Manufacturer: Stage6 R/T · Component group Carburetor: Carburetor complete · Color: black · Surface: varnished · Carburetor type: RT-PWK · Mounting type: Flange · Mounting type: Plug connection · Ø Air filter connection: 50 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Area of application: Tuning

Stage6 R/T RT-PWK 24 mm carburetor Stage6 "Black-Edition"

Manufacturer: Stage6 R/T · Component group Carburetor: Carburetor complete · Surface: varnished · Area of application: Tuning · Color: black · Carburetor type: RT-PWK · Nominal diameter: 24 mm · Nozzle thread: M5x0.8 (standard thread) · Mounting type: Flange · Mounting type: Plug connection · Ø Air filter connection: 50 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke

Athena Athesil sealing compound gray (silicone) 80 ml permanently elastic up to 300 °C

Manufacturer: Athena · Material: Silicone · Contents: 80 ml · Color: gray · Area of application: Chemistry · Temperature resistance (min.): -40 - 300 °C

Stage6 reed valve block VForce 3 by Moto Tassinari

Manufacturer: Stage6 · Number of flaps: 8 pcs · Hole spacing: 52 mm

Stage6 adapter intake manifold Dell'Orto / Polini CP carburetor 21 mm

Manufacturer: Stage6 · Material: Rubber · Ø inside: 21 mm · Hole spacing inlet: 60 mm

Stage6 adapter intake manifold Mikuni carburetor 24 mm

Manufacturer: Stage6 · Material: Rubber · Ø inside: 24 mm · Hole spacing inlet: 60 mm

Stage6 adapter intake manifold PWK carburetor 19 - 28 mm

Manufacturer: Stage6 · Material: Rubber · Ø inside: 30 mm · Ø inside: 33 mm · Hole spacing inlet: 60 mm

Heat protection tape with fastening blue 5 m

Material: Chrome steel (colloquially known as stainless steel) · Material: Fiber · Color: blue · Width: 50 mm · Total length: 5000 mm · Thickness: 1.5 mm

ADDY engine housing GME "der.pruefstand-Edition" | Puch E50

Manufacturer: ADDY · Material: Aluminum

ADDY engine housing GME spindled "der.pruefstand-Edition" | Puch E50

Manufacturer: ADDY · Material: Aluminum

Intake manifold 25 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Manufacturer: Made in Switzerland · Material: Chrome steel (colloquially known as stainless steel) · Ø inside: 25 mm · Hole pattern [mm]: 55 / 60

Intake manifold 29 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Manufacturer: Made in Switzerland · Material: Chrome steel (colloquially known as stainless steel) · Ø inside: 29 mm · Hole pattern [mm]: 55 / 60

Malossi 47 mm cylinder kit BIG DEPS incl. head 10 mm KoBo | Piaggio Ciao, Bravo, Boxer

Nominal diameter: 47 mm · Manufacturer: Malossi · Material: Aluminum · Surface: sandblasted · Displacement: 75 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 49.9 mm · Ø Outlet outside: 22 mm · Ø Outlet outside: 27 mm · Ø outlet inside: 18 mm · Ø outlet inside: 24 mm · Ø piston pin (B): 10 mm · Outlet type: clamped · Outlet type: slanted · Hole spacing outlet: 23 mm · Hole spacing outlet: 38.5 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 3 pcs · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No · Area of application: Tuning

swiing® ingenious bearing & shaft seal set Racing C3 / FPM (new model) | Puch E50

Manufacturer: swiing® ingenious parts · Number of components: 7 pcs · Area of application: Racing

DMP clutch "Racing" aluminum reinforced | Puch E50

Manufacturer: DMP · Material: Steel · Material addition: Chrome steel (colloquially known as stainless steel) · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs · Ø outside: 94 mm · Thickness: 22 mm · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning

MBR cover diaphragm inlet Gilardoni italkit | Puch

Manufacturer: MBR · Material: Steel · Surface: raw · Area of application: Tuning · Ø mounting hole: 6.3 mm · Width: 48 mm · Total length: 72.5 mm · Thickness: 5 mm · Number of fixing points: 4 pcs · Hole pattern [mm]: 60 x 35 mm · Mounting type: Screws

swiing® revival gasket set cylinder | Puch Supermaxi LG1, LG2 (Cat)

Manufacturer: swiing® revival parts · Number of components: 4 pcs · Material: Aluminum · Material: Sealing carton · Material: Sealing paper · Area of application: Standard · Ø cylinder: 38 mm · Ø outlet inside: 22 mm · Hole spacing inlet: 32 - 38 mm · Hole spacing outlet: 42 - 44 mm · Hole pattern [mm]: 44 x 44 mm · Decompressor: No

Barikit piston 48 mm MetraKit cylinder oversize | Puch

Manufacturer: Barikite · Ø outside piston (A): 47.95 mm · Compression height (C): 22 mm · Curvature (D): 3.45 mm · Total piston height (E): 52.45 mm · Number of piston rings (F): 2 pcs · Piston ring mold: Rectangular ring · Nominal diameter: 48 mm · Piston ring impact: Internal fuse (IS) · Piston ring height: 1 mm · Ø piston pin (B): 12 mm · Weight piston kit: 124 g

Barikit piston rings Ø 47 mm | Puch

Diameter: 47 mm · Manufacturer: Barikite · Thick piston ring: 2 mm · Piston ring mold: Rectangular ring · Nominal diameter: 47 mm · Piston ring impact: Internal fuse (IS) · Height: 1 mm

Polini air filter adapter Ø 34 mm carburetor Polini CP

Manufacturer: Polini · Material: Plastic · Color: black · Ø inside: 47 mm · Ø outside: 47 mm

GPO air filter hose for mushroom air filter grille Ø 28 - 32 mm

Manufacturer: GPO · Material: Rubber · Color: black · Mounting type: Bride · Mounting type: Plug connection clamped · Ø inside: 28 mm · Ø inside: 32 mm · Ø outside: 40 mm · Total length: 72 mm · Number of fixing points: 2 pcs

Intake manifold 29 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Manufacturer: Made in Switzerland · Material: Chrome steel (colloquially known as stainless steel) · Ø inside: 29 mm · Hole pattern [mm]: 55 / 60