Socket axle set with closed groove ball bearings (Ø 29 mm) for front cast hubs (Leleu) on your Puch moped / moped.
The threaded shaft set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The wheel axle set works with Leleu front wheel hubs, which are installed in cast rims.
The cable ties show you where to fit what:
- Red cable tie: wheel hub
- green cable tie: brake anchor plate
- Yellow cable tie: Replacement disk for the speedometer drive (the disk is removed if a drive is fitted)
- Blue cable ties: fork braces
Note: When mounting the ball bearings, it is important to note that the long spacer bush between the two ball bearings must be clamped to ensure that the two bearings press with the inner ring on the bushing. If this is not observed, the ball bearings will inevitably jam.
| Manufacturer | swiing® ingenious parts |
| Ball bearing closed | Yes |
| Material | Steel |
| Surface | galvanized (blue) |
| Thread type | MF12x1 (fine pitch thread) |
| Total length | 165 mm |
| Ø inside | 12 mm |
| Width | 34.5 mm, 6.6 mm, 11 mm, 2.7 mm |
| Ø shaft | 11.95 mm |
| Height | 9.9 mm, 5.9 mm |
| Shank length | 74.5 mm |
| Ø outside | 29.02 mm |
| Thread length | 50 mm, 40.5 mm |
| Width across flats | 19 mm |
| Puch |
Ratings
Accessories & related products
Hot 
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® ingenious parts · Ball bearing closed: Yes · Ø shaft: 11.95 mm · Shank length: 74.5 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Thread length: 40.5 mm · Thread length: 50 mm · Ø inside: 12 mm · Ø outside: 29.02 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm
EUR 46.20
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Surface: galvanized (blue) · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Thread type: MF12x1 (fine pitch thread) · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Diameter: 29 mm · Thread length: 29 mm · Thread length: 53 mm · Ø shaft: 19 mm · Width across flats: 19 mm · Shank length: 100 mm
EUR 46.20
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Material: Plastic · Material: Steel · Manufacturer: swiing® ingenious parts · Bearing type: Deep groove ball bearing · Inner ring width: 9 mm · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Width: 9 mm · Ø inside: 12 mm · Ø outside: 29.02 mm
EUR 10.60
GPO speedo drive 17" with lugs 12 mm axle | Puch Maxi S / N, X30 Sport NS / NL, NG-2AH, X30 Velux
Material: Aluminum · Manufacturer: GPO · Place of use: left · Place of use: right · Total height: 10 mm · Ø axle: 12 mm · Wheel size: 17 " · 4-edge speedometer cable: 1.8 mm · 4-edge speedometer cable: 2.6 mm · Ø mounting hole: 12 mm · Ø outside: 41 mm · Thread type: MF10x1 (fine pitch thread)
EUR 33.10
Explore categories from Hub & axle
Moped fans also bought
GPO sprocket 45 teeth black | Puch Maxi, Puch X30 NG-2AH
Manufacturer: GPO · Material: Steel · Surface: powder-coated · Chain pitch: 1/2" x 3/16" · Chain type: 415H · Number of teeth: 45 pcs · Thickness: 4.5 mm · Color: black · Number of fixing points: 6 pcs · Hole spacing 2: 68 mm · Ø mounting hole: 6.7 mm · Ø inside: 94 mm · Hole spacing: 36.5 mm · Cranking (offset): 8 mm · Ø bolt circle: 105.5 mm
EUR 23.60
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Area of application: Standard · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm
EUR 7.00
swiing® revival wheel axle LELEU & Grimeca wheel hub cast wheel rear | Puch
Surface: galvanized (blue) · Manufacturer: swiing® revival parts · Material: Steel · Thread type: MF12x1 (fine pitch thread) · Ø outside: 11.8 mm · Total length: 185 mm · Thread length: 26 mm · Thread length: 52.5 mm · Ø shaft: 11.9 mm · Width across flats: 19 mm · Shank length: 100 mm
EUR 17.70
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Surface: galvanized (blue) · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Thread type: MF12x1 (fine pitch thread) · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Diameter: 29 mm · Thread length: 29 mm · Thread length: 53 mm · Ø shaft: 19 mm · Width across flats: 19 mm · Shank length: 100 mm
EUR 46.20
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Surface: galvanized (blue) · Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Material: Steel · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm
EUR 36.70
SKF 6001 2RSH Ball bearing 12/28/8
Bearing type: Deep groove ball bearing · Stock number: 6001 · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RSH - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Ø outside: 28 mm · Ø inside: 12 mm · Width: 8 mm
EUR 15.30
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
