Complete clutch assembly, equipped with 100 mm diameter clutch discs, a clutch bell (your choice), and NewFren starter plates, compatible with your Piaggio Ciao, Si, Bravo, and Boxer moped with Variomatic transmission.
Also compatible with your Super-Bravo with Variomat; most commonly found on the popular kick-start models.
High-quality oil seals, correctly installed shims, lubricated needle bearings, and a precisely fitting bearing housing are the hallmarks of this converter clutch.
In the selection window, you can choose between a converter bell from CIF, Malossi, or Polini.
Notes:
For installation on a Piaggio Ciao, the pulleys must be turned down to approx. 96 mm or the frame must be slightly sanded down.
The required belt length when used with a Rennvario on the Ciao ranges from 950 mm (rear engine position) to 975 mm (front engine position). For Piaggio Si models, the length ranges from 1134 mm to 1150 mm.
The installed backpressure spring has the same spring force as the original. For a higher starting RPM, you can replace it with a stiffer version as needed. When installing, make sure the spring tip does not protrude too far into the pulley and could damage the belt.
The starter plates in this set are not yet mounted in the variator bell housing. The components are shipped as individual parts.
You can find additional parts for your Piaggio with Vario drive in the accessories section.
A good, affordable standard replacement part. GPO – GOOD PARTS ONLY.
Original Piaggio part numbers:
221171, 124775 (converter unit)
190312 (clutch bell)
120870 (starter linings)
220441 (retaining plate)
006426 (retaining ring)
Manufacturer: GPO · Gearbox type: Vario · Ø outside: 100 mm · Hardness level Counter pressure spring: Standard (30 kg - steel-colored) · Area of application: Standard · Alternative version of the Piaggio OEM number: 221171, 104649 · Ø inside: 93.5 mm · Number of jaws: 3 pcs · Number of springs: 3 pcs · Angle pulley: 17 ° · Thickness: 74 mm
Manufacturer: Piaggio · Material: Spring steel · Spring design: Leaf spring · Piaggio OEM number: 220441
Manufacturer: Piaggio · Material: Spring steel · Fuse type: Outside · Place of use: Clutch · Nominal diameter: 25 mm · Piaggio OEM number: 006426
Manufacturer: CIF · Piaggio OEM number: 249816 · Gearbox type: Vario · Number of jaws: 2 pcs · Number of springs: 2 pcs · Area of application: Standard, Original · Material: Steel, Composite materials
Material: Steel · Total length: 12.5 mm · Width: 3 mm · Height: 4.9 mm
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo Gilera CBA Gilera Citta |
Accessories & related products
Stage6 6.5 - 9.5 g vario weight set Ø 16 x 13 mm
Manufacturer: Stage6 · Number of weights: 24 pcs · Weight Standard weights: 6.5 g · Weight Standard weights: 7.5 g · Weight Standard weights: 8.5 g · Weight Standard weights: 9.5 g · Ø Weights: 16 mm · Length Weights: 13 mm · Gearbox type: Vario
EUR 39.00
Hot 
swiing® ingenious pulleys Ø 96 mm | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® ingenious parts · Material: Steel · Material: special bearing bronze · Ø Outer pulley: 96 mm · Surface: gas nitrided · Gearbox type: Vario · Alternative version of the Piaggio OEM number: 103382 · Alternative version of the Piaggio OEM number: 103823 · Alternative version of the Piaggio OEM number: 220923 · Alternative version of the Piaggio OEM number: 220924
EUR 142.30
Not in stock
swiing® revival counter pressure spring (original force) torque converter | Piaggio Ciao, SI, Bravo
Spring design: Pressure spring · Ø inside: 36 mm · Ø outside: 43.5 mm · Ø wire: 3.8 mm · Manufacturer: GPO · Material: Spring steel · Surface: galvanized (blue) · Total length: 80 mm · Number of components: 1 pcs · Piaggio OEM number: 104662 · Piaggio OEM number: 221172
EUR 15.30
Explore categories from Variomatic belt drive
Moped fans also bought
GPO converter Vario Ø 100 mm without bell housing | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Number of jaws: 3 pcs · Ø inside: 93.5 mm · Ø outside: 100 mm · Angle pulley: 17 ° · Number of springs: 3 pcs · Gearbox type: Vario · Thickness: 74 mm · Hardness level Counter pressure spring: Standard (30 kg - steel-colored) · Area of application: Standard · Alternative version of the Piaggio OEM number: 104649 · Alternative version of the Piaggio OEM number: 221171
EUR 130.40
Not in stock
Working late? Evening hours on Thursday until 20:00
